Categories
Information

OxyDoser PUREair - Outside of USA

 
 
 
 
 
Back to List
 
$235.00 - $280.00
Qty:
Location:
Shipping:
 
 
Additional Info
pdf OXYDOSER INSTRUCTIONS.pdf (562.3 KB)
 

International Orders. Make sure to Mark the Correct Shipping Location. We typically ship orders within 1 week of order placement.

 

OxyDoser­™ PUREair

Hydroponic and Actively Aerated Compost Tea Bubble Generator

 

For Pricing please contact your local Hydroponics Retailer.

 

The OxyDoser™ PUREair produces bubbles and Oxygen Saturation using two different techniques at the same time while using only the power of a low wattage Hydroponic Water Pump. The OxyDoser™ PUREair can also be converted from low pressure to high pressure to make smaller bubbles and can be used with either normal air or compressed Oxygen.

 

For low pressure use. The device is plumbed in line with a 160-250 gph pump and a standard 1/4" air line is attached to the air nozzle. There are no moving parts. In low pressure mode this device can saturate 100-200 gallons of fluid. Multiple OxyDoser™ PUREair devices can be used for larger volumes or you can use in high pressure mode. See low pressure operation below.

 

 

When the pump is started, water is forced into the OxyDoser™ PUREair's two patent pending nozzles, one at each end. Air is sucked into the air line via the vaccuum created by the swirling motion of the water inside the OxyDoser™ PUREair. One end produces MicroBubbles and the other produces Liquid Film. Both of these mixture technologies ease the transfer of gas in and out of the water. Easing this transfer matters, this is how your hydroponic fluid gets Oxygenated. Air Bubbles from an Air Stone can do this, the OxyDoser™ PUREair can do it much better. 

 

For high pressure use. The device is plumbed in line with a 50 psi pump and the "mushroom" thin film top is removed. A standard 1/4" air line is attached to the air nozzle which can be left open to the air or attached to compressed Oxygen. In high pressure mode, the device can saturate 1000's of gallons of fluid. There are no moving parts. See high pressure operation below.

 


Microbubbles are simply small bubbles. MicroBubbles are good for plants for two reasons:

 

1. MicroBubbles have more Surface Area for a given volume of air vs. large standard Air Stone bubbles. This greater Surface Area increases the amount of Oxygen that can be transfered into the Water before the bubble is gone. MicroBubbles also stay in suspension longer before they pop, also allowing for increased saturation.

 

2. MicroBubbles have an Ionic Charge. This Ionic Charge allows for Ionic Bonding with Charged Nutrients, thus allowing for better utilization and transfer of your N-P-K and MicroNutrients.

 

Nutrient Film is really water wrapped around gas, in stead of gas in water. You see nutrient film when you see water boil or when you see soap foam. The bulbed housing on the OxyDoser Air forces all of the fluid that escapes from that and of the unit to go through the Liquid Film process. This Liquid Film has increadibly high Surface Area relative to volume of fluid and is even better at producing Oxygen saturation than MicroBubbles, but does not produce Bubbles with an Ionic Charge. This is why we coupled the two halves into one great oxygen producing device!

 

The OxyDoser™ Air gives you both Bubble and Gas Saturation Technologies in one unit with the following benefits vs. Air Stones:

 

1. Increased Oxygen Saturation resulting in more root growth, thus increasing Yeilds.

 

2. Increased Oxygen Saturation resulting in less pathogens such as root rot.

 

3. Production of MicroBubbles with an Ionic Charge which eases Nutrient Transfer to the roots resulting lower Nutrient Concentrations.

 

4. Large Capacity - approximately 200 gallons of full Oxygen Saturation can be achieved with one unit. Multiple units can be used for larger volumes or you could consider the OxyDoser™ Pure.

 

5. Displacement of other contaminate gases present in the Water such as CO2 from the Grow Room. CO2 is for the leaves, not the roots.

 

6. 85% less heat generated from the assoicated 250 gph water pump vs. a 110 lph air pump. This reduces the burden on fans and cooling devices.

 

7. Save approximately $150/year using a 250 gph water pump vs. a 110 lph air pump. The unit will pay for itself in less than 2 years on power consumption alone.

 

8. No Air Compressor Noise, you only hear water flowing.

 

9. Flowing water from device serves to mix and evenly distribute Oxygen Saturated Fluid.

 

10. Way cooler to talk about at Cocktail Parties.